• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

Although it's easy to believe a door is beyond repair There are many easy fixes that can make a huge difference. Let's start by shifting.

To reduce the size of an opening, you must open the door and press it firmly into the frame. Use a jack plane or block to remove small pieces of wood from the binding points.

The Frame

The door frame is among the most important components of your home. It is crucial to ensure the security of your home, as it prevents water damage. But it's also prone to being damaged. Whether from bad weather or break-ins, or just normal use, door frames could become damaged. If they do, this could result in large holes, a poor latching system and a dull appearance. Fixing your door frame is a matter of just a few steps.

The first step is to take the trim, also known as molding, from around your door opening. This can be accomplished with the hammer and chisel, or door panels (Nagievonline.com) a power saw. After the trim is removed, make a note of the measurements and replace it after the repair.

You should then inspect any damaged or rotted areas of the door frame. If you find any rotten areas, you will need to buy and replace the wood pieces. These are typically available at the local hardware store, and should be made of a material that will match the frame of your door. It is best to avoid using pressure-treated wood since it tends to twist and warp over time.

After you have replaced any rotten sections of the frame, you will be required to ensure that it is secured in place. A good way to do this is by using the shim, which is essentially a piece wood that is placed between the frame and the wall. The shim will provide extra support for the frame and keep it from moving.

After you've replaced any shims, it is an ideal idea to caulk around the door frame and sill. This will help keep water damage from occurring and protect the frame from insects.

The next step is to put your trim back on the door frame. If you are lucky, your previous trim might be in decent condition, and you could simply put it back in place. If your trim is not in good condition, you will need to buy new trim and repeat the procedure.

The Threshold

A threshold is a strip of wood used to fill and protect the space between the door and the floor. It also assists in preventing snow and water from getting in the entranceway. In addition to being an integral element of the door, a properly installed threshold is also a beautiful feature that will enhance your home's curb appeal. It's time to replace your threshold if it is damaged, worn out, or has been scratched. Installing a threshold can be more complicated than just sliding it under the casing, and nailing it into place. It has to be supported by shims placed between the frame's two jambs.

Cut the old threshold away from the sides using a circular blade (use carbide blades if possible). If you can, pull up the sub sill, the part of the frame which is under the threshold. If it's rotting, replace it at the same time as you replace the threshold.

Use a carpenter's square to trace the layout lines prior to cutting the threshold. Note the right angles for notches that are able to fit around jambs. Home centers sell pre-cut thresholds to match the width of your opening.

Insert the shims, double glazing company (my sources) being sure to place them equally. It is fine to alter the thickness of each shim if needed, but they should be less than 1 1/2 inches in width. It may require some trial and error to make the threshold snug but still in a position to move freely.

Check the suitability of your new threshold by closing the door and testing how well it opens and closes. There shouldn't be any daylight under the door and the sweep at the bottom of the doors should be lightly rubbing the top of threshold.

If the threshold fits well but requires a little more support, apply a construction adhesive to the shims prior pressing them down under the threshold. Repeat the process until you achieve a tight fit and it is able to withstand the weight.

The Hinges

Many hinges on doors rust or deteriorate over time, making it more difficult to close the door. It is essential to fix the hinge so as to close and secure the door properly. When replacing the hinge, ensure that you use one that's similar in size and shape. Also, ensure that the hinge is placed correctly in the mortise and door jamb.

First, check the hinge for any looseness. If the hinge is not tight it will likely to be snagged along the door's frame and rub against its strike plate. Check for scratches in the paint or indents on the frame to indicate the location where the hinge is rubs. If the problem is that the hinge isn't securing enough, use a screwdriver to tighten it. If the hinge is loose, you can try an shim between the door frame and the hinge, or you could have to replace it completely.

You can straighten the hinge knuckles by bent them using a pair of large pliers with a tongue and groove or an adjustable wrench. This can be done by carefully bend the knuckles manually using a pair tongue-and-groove pliers, or an adjustable wrench, however it's recommended to work on just one individual knuckle at a given time to ensure that you don't bend the hinge leaf out of its mortise.

It's also possible the screws holding your door hinges in place have been stripped. If this is the case, you can replace the screws to give them a better grip on the hinges.

If the hinge isn't damaged, and the screw holes aren't clogged then you can use a syringe to inject carpenter's adhesive into the mortise and joint of the hinge. Then screw the hinge into place, and secure it using a screwdriver or drill. If you're putting in new hinges, it's a good idea to mark the locations of the pilot holes on the door as well as the door frame so that you can be certain to place the screws exactly where they were as the old ones.

The Hardware

Many people don't think about door knobs, levers, double glazing company and locksets until they stop functioning properly. Fortunately, many of these hardware parts are repairable. Replacing a door handle or knob is typically a matter of picking out the piece that best matches the style and design of your house and then putting it in place. For doors with exterior doors it's recommended to add weather stripping too.

If you have a door which is difficult to open, you may be able to fix the issue by lubricating your lock assembly. Many types of locks, door handles, and hinges are susceptible to squeezing when their worn surfaces are dirty or dry. Keeping these parts clean and lubricated is a cheap way to keep them operating in a safe manner.

Some of the most common problems with door hardware are broken or loose handle screws or locks that won't turn when you insert the key, and Patio Doors (Continued) hinges that rattle or bind. In the majority of cases, you can tighten the screws or replace them entirely. In some instances however, it's recommended to remove the lock and handle from the door and sand the spindle as well as the lock cylinder bore holes, and also the escutcheon hole, to make sure they are free of dirt prior to installing the new hardware.

If you have doors that are difficult to close, it could be necessary to grease its locking mechanism using penetrating oils. For hinges that are squeaky, you can remove and clean the hinge pins, and then replace them with longer screws that will be more likely to secure.

If you need to replace a lock, handle, window replacement fitters (Continued) or hinge, be certain to choose a product that is compatible with the current hole size on your door specialists and jamb. This information is typically found on the packaging or the manufacturer's website. For example, doorknobs or levers require a hole that is at a certain spread (the distance from the center of the lock hole to the knob). Check the backset to see whether the replacement fits.