• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is an easy and inexpensive method to increase your home's security. The process is not for all. It requires a certain amount patience and skill.

The cylinder is located within the knob's body. The cylinder is what recognizes the key when it is put into the lock.

The old lock can be removed

The first step to replace a door lock is to take out the lock that was previously in use. It is a fairly simple process, but you must keep a few things in mind. First, ensure that the lock you choose to install is the correct size for your door. This will ensure it is securely fitted and won't leave a gap in the latch or deadbolt.

Once you have removed the latch plate look for two screws or bolts on the inside of the casing that hold the casing and the halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock off the door. If you have a mortise locking mechanism there is an anchor screw that connects the handle to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

Remove the deadbolt and latch plug from your door jamb. Then, you can install your new lock. If you're replacing a mortise, you must take a measurement of the distance between the lock case and your door's edge to ensure that the new lock will fit.

You may want to replace your lock for a variety of reasons, such as when you suspect that someone else has the key, or if you have new roommates. You can save money if you remove the lock yourself instead of paying an expert. It's easier than many people think and can be done in a few minutes.

Remove the handle and trim of your upvc door lock. Then, pull the trim loose using a flat screwdriver. You will be able to pull off most of it, and in some instances the handles could come off completely. Then, check the handle for a small pinhole on the interior side and insert a straightened paper clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Next, examine the interior side of the lock for another small tab and press it with a flat screwdriver. After the spindle has been removed, you are able to remove the housing and the cylinder.

Making a decision on a new locking system

When it comes time to pick the right lock for your home, you have many choices. Take a look at the various types of locks and select one that matches the design of your door. Think about the backset, which is the distance between the edge and the middle of the hole in the lock. Also consider the cross bore, which is a small hole in the middle of your door frame. Select a lock that is suitable for the door thickness and swing.

Most door locks are graded by BHMA and the American National Standards Institute to give you an idea of how well they are able to withstand the rigors of use and how difficult to pick or disable. A grade 3 lock might be the best choice for a peaceful rural apartment complex, while an entry grade lock could hold up better to the traffic at a busy retail storefront on a busy street.

Most smart door locks require a digital key code to open. If you're concerned about security breaches or hacking you should consult a professional locksmith or the local police department for advice.

Replacing the cylinder

If your pvc door locks lock's cylinder is damaged or broken it can be replaced in just a few minutes by completing a do-it-yourself project. It is crucial to choose the right cylinder and follow the instructions. First, you must remove the knob or handle, if it is present. Then with a screwdriver take off the trim around the lock cylinder. After the trim is removed, you can take off the screws that hold the cylinder with a flathead. The cylinder can then be gently pulled out of the door.

Make sure you measure the length of the new cylinder before installing it. Measure the distance from the center to the left and right sides of the cylinder with a tape measure. Then, purchase another cylinder that has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key becomes stuck inside.

If you have a suitable replacement cylinder, door Lock change place it into the door and turn the key. This will align the cylinder with the carrier which is located usually on the outside of your lock. Then, loosen the set screws that should be only a couple of turns into the head. You will also need to loosen the screw at the edge of the door which secures the case if there is one.

You can replace the old lock cylinder with the new one by inserting it into the case and then tightening the set screws. It is also recommended to reinstall the bracket that connects the cylinder to the lock indicator stem, which you can do by removing three small tabs on the back of the cylinder using needle-nose pliers. Attach the smaller bracket to the back of the cylinder. Then, you should reinstall the strike plate and latch plate, along with the retaining rings fixed to the top of the lock repairs near me cylinder.

Installing the new lock

Start by measuring the door's width if you are replacing an existing lock. Most locksets for residential use come with a thickness of 3/8 to 1 3/4 inches. If your door is more thick you will require a door kit that is thick and includes longer screws, longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed instruction booklet to help you install the new hardware. Before you begin, go through the instructions to ensure you've followed all the steps. The guide will give you a clear idea of how much skill is required to finish the task. If you're changing a lock for the first time, you might need to seek out an experienced friend for Door Lock Change assistance.

Before installing the new lock it is a good idea to cover the openings with tape the old hardware. This will prevent the screws from falling through the holes, and protect any tiles you have installed. It also shields your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with the masking strip or gaffer tape, but you can use any tape you own.

After you have removed the screws that connect the interior half of the lock section to the outside side immediately, pull it back. It is important to do this quickly to avoid the lock from closing accidentally and harming the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the proper position, which is indicated by an arrow. Then, slide the latch plate over the bolt and screw it into the correct position.

Screw the deadbolt to the jamb on the door. Test the deadbolt by throwing it a few times to ensure that it extends all the way into the strike plate and is fully secured. If you're using an electronic smart lock, make sure to follow the included instructions for programming it. This involves downloading an app, registering your email address, confirming your identity, and accessing the wireless network to add your device.