• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons to Change Door Lock

You can replace the lock on your door for a variety of reasons, from upgrading the security of your house to redecorating the entrance. You might also have to change locks if the key gets stuck or is difficult to turn.

Changing your lock is a simple project that even novice DIY homeowners can take on. To begin, gather the required materials.

Take off the lock that was previously used.

Before installing a new lock it is important to take out the old lock repairs near me from the door. This is important in the event that you suspect that someone else might have access to the home. It may also be a good idea if you have recently moved into a home, experienced a break-in or received a new roommate. It is easier than you think and can be done in a matter of minutes.

Begin by removing the screws that hold the deadbolt faceplate onto the door frame. You'll have to take off the screws on both sides of the door to take off the faceplate. This will let you discover what's behind it, and will provide you with a better understanding of how to proceed with the rest of the steps.

After removing the old faceplate, you'll need to remove the bolt, strike plate and the strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusty, you may need to use a chisel hammer it out. If you are using a chisel be careful not to scratch the door frame.

Before you remove the old lock, make sure that the new doorknob and deadbolt fit into the existing holes on the door. The majority of hardware stores and big box stores sell different kinds of locks and will help you find the right one for your needs. If the lock repair you bought does not match your door, send it back and seek assistance.

Look for small dents or depressions in the handle and around the trim when you take off the lock. If you find them, use straightened safety pins or a flat screwdriver to release the handle.

Once the screw inside the handle has been removed you can begin to remove the knob from its spindle. To do this find the set screw at the base of the knob and loosen it. The next step is to remove the knob from the spindle and carefully remove the spindle from the door.

Install the new lock

It's a good idea to change the locks on the doors of your home regularly, especially in the event of a burglary or you move into a new home with roommates. It's easy, affordable and effective to change the lock on your door. With a screwdriver and a few basic steps most people can do it themselves. You might also want to learn how you can change the key on your door lock to ensure that only you have the key.

To start the process, you need to buy a new lock that is compatible with the keyway on your existing lock. You can save money by choosing to modify the lock yourself. Many locksmiths charge an extra fee for this. You can purchase a brand new lock at an hardware store, or even online. A standard deadbolt should fit on all doors however, you'll have to measure the size of your door to ensure that it's a good fit.

Your new lock will often come with a diagram that will show how to put it on the door. You can use it as a reference for drilling the hole, which is much easier than measuring each time. If the template does not line up with your hole then you should take it back to the hardware store and purchase an alternative.

The new lock on the right-hand side of the door. You can check this by looking at the latch, which must be labelled "up" or something similar. Make sure that the latch is seated correctly on the latch plate, then secure it with the screws provided.

If you are replacing the knob lock on your door it is also essential to be aware of the type of lock you're using. Certain knob locks are right-handed. If you're not careful, you could install the knob on the wrong side of the door, which would hinder you from locking it from inside or outside.

When you're done checking the new lock to confirm that it functions. You should be capable of locking the door from both the inside and Change Door Lock the outside, as well as unlock it using a key. If you aren't satisfied with the results you can get a locksmith to fix it.

Test the lock

A lock that does not open is a nuisance but it can also put the safety of your family at risk. It's easy to fix the majority of door lock problems by tackling the issue and lubrication. Make sure that the key is properly cut and the lock assembly isn't loose or dirty. If this doesn't fix the problem, you can try lubricating the door lock actuator using powdered graphite or a silicone-based lubricant.

Make sure that the doorlock switch, wiring harnesses, and actuator connector all work correctly. Refer to the wiring diagram or manual to determine the color code and function of each wire of the door lock switch. Then, test the wires using a light or digital meter to determine if the door lock actuator receives power and ground when the switches are turned on. If you can see the switches switch on and off with voltage, it means the switches are in good working order and the actuator will require replacement.

If the switch seems to be working, but the actuator doesn't move when you turn the knob it could be an issue with the actuator itself. The actuator cylinder is loaded with spring pins that keep the cylinder from rotating until the key is inserted, which it pushes the pins up to fit the key's height in the location. The cylinder then begins to turn opening the lock body and allowing the handle latch.

If the door lock actuator still not working, you can remove it by using a small screwdriver. You will need to release the bolt that locks it first and then remove the plastic cover which holds the electrical connector. Then, disconnect the door lock actuator and let it fall down. Then, you should be able identify and remove the two 10mm bolts holding the actuator in place. Once the actuator is removed, you'll be able to disconnect the black electrical connector and remove it together with the lock and actuator assembly.

Replace the key

Whether you have an unkeyed door knob or deadbolt, when it isn't functioning properly, you must either change the lock's key or rekey it or replace it completely. It's not too difficult and could save you money. It is recommended to hire an expert locksmith inspect the locks for any problems prior to starting. This will provide you with peace of mind that your home is secure and safe.

Take off the exterior faceplate of the doorknob/deadbolt. There may be screws holding it in place, you need to remove them, use a screwdriver to loosen them, and then pull the faceplate off. Then, use a flat head screwdriver to take off the interior faceplate. After you have removed the faceplate, you can remove the bolt and screw from the lock cylinder.

A locksmith can determine whether you require a replacement or rekey your lock. They can also provide suggestions on the most secure measures for your home. They can also make necessary modifications to your door and frame for an ideal fit. They also offer a guarantee on their work.

If you choose to rekey your lock, you must first purchase the new key. It is crucial to select the lock key that is fitted snugly. A key that is not the right size may harm the internal mechanism of a lock and stop it from functioning. To test the size of a key, insert it into the lock. If it is in a flush with the plug it's of the correct size. If the pins stick out of the top of the plug, they're not long.

You may need to replace your door lock for a variety of reasons, such as:

If you're moving into a previous owner's home or if you lose keys, rekeying your lock could be a more affordable option than replacing a upvc door lock it. It's also less costly than a full replacement. However, there are circumstances where rekeying your existing lock isn't an option. For example, if the lock is damaged or repeatedly jammed, it's probably time to replace it.