• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

It's easy for people to believe that doors can't be fixed, but there are many simple fixes which can make a big difference. Let's begin with the shimming.

To shim a door open the door and press it with force against the frame. Utilize a block or jack plane to remove small pieces of wood from the binding points.

The Frame

The door frame is an essential component of your home. It offers security, protects against water damage, and gives your home a beautiful appearance. However, it is also susceptible to being damaged. Door frames can be damaged by harsh weather or burglaries, or simply normal use. If they do, it can lead to large holes, weak latching and a shabby appearance. Fixing your door frame can be done in a few simple steps.

First, remove the molding or trim around the opening. You can use a hammer, an axe, or a power saw to take off the trim. After the trim is removed, take note of the measurements to replace it following the repair windows.

The next step is to look over any damaged or rotten areas of the door frame. If you discover any rotten wood, you will have to replace it. These are usually found at the local hardware store and Repairing Glass should be made from a material that will match the frame of your door. Avoid pressure-treated wood as it tends to twist and warp with time.

After you have replaced any rotten or damaged sections of the frame, you will be required to ensure that it is secure in the right place. One method to do this is by using the shim, which is essentially a piece of wood that is placed between the frame and the wall. The shim can provide additional support for the frame and keep it from moving.

After you've replaced the shims it is a great idea to seal the frame and the sill of your door. This will stop further water damage and protect your frame from insects.

The next step is to put your trim back on the door frame. If you're lucky enough, the old trim may still be in good shape and you'll be able to put it back on. If your trim isn't in good condition, you will have to purchase new trim and repeat the procedure.

The Threshold

A threshold is a piece of wood used to cover and seal the gap between the door and floor. It also helps prevent snow and water from accumulating in the entranceway. In addition to being an integral element of the door, a well-installed threshold can also be a gorgeous accent that adds to your home's curb appeal. It's time to replace your threshold if it's damaged, worn, or scuffed. Installing a threshold is more complicated than just sliding it under the casing, and nailing it into place. It needs to be supported by shims that are put between the frame's two jambs.

To remove the threshold first, In My Area cut it away from the sides of the door frame with circular saw (use a carbide blade, if possible). If you can remove the sub sill, repairing double glazing repairers glazing (http://safety-lab.co.kr) the part of the frame that runs underneath the threshold. Replace it if it's rotten in the same way as you replace the threshold.

Before cutting the threshold to size, you can use a square for marking layout lines on it, noting right angles to make notches that will fit around the jambs. You can also purchase thresholds pre-cut to the width of your doorway at a home center.

Install the shims, making sure to space them equally. It is fine to alter the thickness of each shim when required, but keep them not more than 1 1/2 inches in width. It might take a bit of trial and error to get the threshold snug but still capable of moving freely.

Close the door and see whether it opens and closes. There shouldn't be any daylight under the door, and the sweep on the bottom of the door should lightly rap against the top of the threshold.

If the threshold fits perfectly but requires a little more support, apply a construction adhesive to the shims before pressing them down under the threshold. Repeat the procedure with additional shhims until you have a tight fit that can withstand the weight.

The Hinges

A lot of hinges for doors become rusty or degrade over time, making it difficult to close the door. It is important to upvc window repair the hinge in order to shut and secure the door securely. If you're replacing the hinge, be sure to use a similar one that is an excellent match in terms of size and shape. You should also ensure that the hinge is placed correctly in the mortise and door jamb.

First, examine the hinge for any looseness. If the hinge is loose it is likely to bind along the door's frame and rub on its strike plate. Check for scratches in the paint or indents in the frame that indicate the area where the hinge is rubbing. If the hinge is not tight enough then tighten it up using a screwdriver. If the hinge remains too loose, you may need to replace it. You can try putting to put a shim between the door frame, and the hinge.

You can straighten the hinge knuckles by bent them using a pair of large tongue-and-groove pliers or an adjustable wrench. You can do this by carefully bending the knuckles by hand [Redirect-302] using a pair tongue-and-groove pliers or an adjustable wrench, but it's best to work on just one individual knuckle at a given time to ensure that you don't bend the hinge leaf out of its mortise.

You might also notice that the hinges on your doors are loose because the screws that hold them in place have stripped. If this is the case, replace the screws with longer ones to give them a better grip on the hinges.

If the hinge isn't damaged and the screw holes are fine you can use a syringe inject carpenter's glue into the hinge mortise and joint. Then you can screw the hinge back into its place and secure it with an screwdriver or drill. If you're putting in new hinges it's a good idea mark the locations of the pilot holes on the door and the frame of the door to make certain to place the screws in exactly the same place as the previous ones.

The Hardware

The majority of people don't give much thought to door knobs, locks, or [Redirect-Java] levers until they stop working properly. They are repairable. Replacing the knob or handle on a door is typically a matter of picking out the piece that best matches the style and appearance of your home and putting it in place. For exterior doors it's usually a good idea to add weather stripping as well.

You may be able solve the problem of a door that's difficult to open by lubricating your lock assembly. Many hinges, handles and locks may become stuck when their wear surfaces get dry or dirty. It is inexpensive to keep these components clean and lubricated.

Some of the most common issues with door hardware are loose or broken handle screws locks that don't turn when you insert the key, or hinges that squeak or become bind. In most cases you can tighten the screws or replace them altogether. In some instances it's best to take the handle or lock from the door and then sand the spindle, lock cylinder bore hole and escutcheon holes make sure they're clean before installing the new hardware.

For doors that are difficult to close, you may require lubricating the locking mechanism with penetrating oils. Clean and reinstall hinge pins using longer screws to repair doors that are squeaky.

If you're planning to replace a handle, lock or hinge, be sure to select a model that is compatible with the current hole size on your door and jamb. You can usually find this information in the packaging or on the manufacturer's website. For example, a deadbolt requires a borehole with a 1 1/2-inch or 2 1/8-inch diameter, and doorknobs and levers need holes that have a different spread (the distance between the center of the knob and lock holes). Examine the backset to determine whether the replacement fits.