• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Glass Windows

When a window pane breaks the gaps that result let moisture into the home. These holes decrease energy efficiency as well as the resale value.

Fortunately, a replacement is an affordable and simple option. You will need metal glazing points, pliers, latex glazing putty and the heat gun. Wear safety glasses and gloves.

Measure the Window

The right measurements can make or break your window replacement project. If you purchase the wrong size replacement window, it could be costly to install. It may also not fit correctly in the opening. Follow these steps to measure your old window before removing it.

Start by measuring the frame width in three areas including the top, middle and the bottom. Note each measurement with tape measure. Keep in mind that the window's width does not include any trim. Next, measure the height of the frame in three places on the left side, the middle and the right side. Select the shortest measurement and record it. Then subtract 1/4 inch from each of these measurements to arrive at an approximate height and width measurement.

Be sure to include any jamb trim when measuring the height. Take note of the distance between the inside of the jambs on the left and right side to the head jamb. If the window is finished in the drywall, take measurements up to the top.

Once you have the measurements, you can remove the nails and putty that are holding the old pane. If the molding on one side of the frame has nail holes or holes in the paint, a pull-type scraper or an old chisel can work. If there are only tiny pieces of molding, simply cut them loose using a utility knife. Then you can take measurements for the new window frame.

Remove the Old Pane

Even the most durable of windows can be cracked by a ball that is flying out of control, a branch that flies too high, or cleaning done with excessive energy. In the majority of cases, glass is held in place with glazier's putty as well as small metal clips referred to as glazier's points. The first step to replace glass on window a broken pane is to take off the old glazing putty and points. The replacement is then able to placed in its place and coated.

Wear protective gloves to avoid damaging the new glass and work on an even surface. Utilize a utility knife to remove the putty from the rabbet. If the old putty is difficult to remove, try softening it using a hair dryer before cutting it with your knife. The use of heat guns is to remove hard-to-remove putty. However you should only employ them in short bursts.

After the old putty is gone after which you can number the points or nail fasteners and note where they were placed in the frame. Utilizing pliers, remove the old nails or brads. If the frame has been painted the paint needs to be removed using the help of a knife before you remove the nail.

Find the width and depth within the frame opening if you have to purchase a replacement glass. Subtract 1/8 inch from both sides to ensure that the glass you purchase is suitable. You can typically find the right size in numerous hardware stores and home improvement stores. You could also have the glass cut to the exact size by most glazing and glass firms. If you do this, be certain to order the glass piece one quarter-inch smaller than the opening of the frame.

Set the New Pane

If you're planning to replace a window pane, it's a good idea invest in energy-efficient glass. This will save you money on your heating and cooling bills and also help you conserve the environment. You can also select a more decorative or historic glass style to add to the aesthetic of your home.

Before you get started, clean the new pane to ensure there are no smudges or streaks. Utilize a utility blade to scrape the old glass putty and then clean away any residue. It is recommended to work in a well ventilated area, and you should have mineral spirits or a different solvent to clean up the mess, if needed.

To install the new window pane begin by applying a fine bed of compound to the backstop. Place the pane into the rabbets and press it down to ensure it is secured. Work until the window is at the center of the opening and just 1/8 of an inch remains between the glass face and the rabbet.

While you're there, scrape and sand the surrounding wooden rabbets Then, coat them with an exterior primer. This will stop water from getting into the new pane and causing damage to it. After the primer has dried, knead the putty until it is soft and Replace Glass Windows malleable. Then, push it into the rabbets. It's OK to be a little rough here, as the goal is to make an effective seal that lasts.

Apply the Putty

In the past, before double and upvc, the majority of windows were formed from steel (usually galvanized) or timber, and one glass pane was dropped into them. The glass was then fixed by tiny nails, referred to as spriggs, which were put into frames. You can often see these nails in the wood and if you can a good look at them, it should be possible to remove them without damaging the glass. If they won't budge then you may need to spray them with silicone sealant remover or dissolver as this will dissolve the glue that holds them and allow you to pull them free.

You can also use a heatgun to loosen the old glazing putty, making it easier to chip with a cutting instrument. This is a more secure option but you must be careful not to focus the heat on a single area of the wooden surface and cause cracks. Always wear gloves with leather and eye protection when working with a heat gun and ensure the window is secured to prevent it from moving when you cut out the old putty.

It is important that you clean the frame using the rag dipped in mineral turpentine before applying any new putty. This will wash away any dried putty and provide the surface with more grip. Apply a thin layer white putty on the inside edge of groove where the glass will be placed. It is vital to get this right or the window won't sit in the groove properly. The glazing points can be replaced if required after the putty has been shaped and smoothed with a rag soaked in turpentine.

Apply the Oil

You'll need to take out either the sash (the sliding portion of the windows that houses the glass) or the jamb liners, which are the sides of the frame. Press in on the jamb liners made of vinyl which are on the sides of the frame and pull out the sash's top. Then give a twist to release the springs that hold the latch at the bottom. Slider windows are usually the easiest to take off of the frame, as you can simply lift up the bottom of the sash.

After the old pane has been removed, scrub the frame using a wire brush and a utility knife to clean any dirt and paint that has accumulated in the grooves around the beadwork for the glazing. You can also soften the glazing putty with a heat gun, but be cautious not to scorch the wood. If needed, sand the grooves to bare wooden.

Purchase your new window replace glass glass from an all-service hardware store once the sash is removed. Make sure you accurately measure the opening and subtract 1/8 inch to account for shrinkage. Make sure to purchase an assortment of glazing points to hold the glass while the new putty is hardening.

Before you begin to re-glaze the window replacements near me, apply a heavy coat of linseed oil on the wood frame and allow it to soak in completely. This will lubricate your wood and help the new glue last longer. You can then continue with the remainder. You can also use the same oil from linseed to lubricate the tracks and hinges on sliding doors also. This will keep the doors and windows functioning smoothly and will prevent them from sticking or forming a bind.