• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Simple Door Repairs You Can Do Yourself

Your door is your primary barrier against dust, water, bugs and heat. It's also the primary way that you control how much conditioned air is able to escape from your home.

Tiny dents and dings are simple to repair with spackle. It's cheap and readily available at any hardware store. It's also a good choice, but may take longer to dry.

Repairing a Loose Handle

A door handle or doorknob that's loose can be a major troublesome and even dangerous particularly for those who use the doors frequently. This problem can get worse over the years and result in a larger repair or replacement.

The screws that join the handle to the base are what hold most door handles in place. These screws may loosen over time due to a variety of causes. They are most often loose because of normal wear and tear, however they can also come loose due to abrasion or moisture. Additionally, they can be loosened by dust and dirt that build up in the hardware over time.

The first step is determining which screws are loose. Based on the type of handle, this may be done without having to remove the knob. You may find an opening in the handle to place the flathead, or a hole for a paperclip. If it doesn't, you'll need to take off the rose to expose the inner screws. Once you've reached the base, it's a good idea remove the knob from the door and remove the base.

Once the inner screws are exposed, you'll be able to tighten them using the same technique as you did to loosen them. If needed you need to apply a threadlocker to the screws to stop them from becoming loose again.

Once the screws are securely tightened, you can reinstall the doorknob and handle, placing the base back into place. It's a good idea to test the handle and see how it performs before replacing any decorative faceplates, or other accessories. Examine the handle frequently to make sure it's in good condition. You might also want to apply a coat or polish to keep its appearance. If you do need to apply a layer of polish or wax, apply it with a soft cloth. You don't want to use anything that can cause damage to the hardware.

Repairing a Door that Swings Open

If your door opens when you close, that could be because the latch is not properly aligned with the strike hole in the frame. This is a common problem that can be solved by following some simple steps. Experts from Family Handyman explain that the first step is to lean back and examine the gap between the frame and the door. Most of the time, this gap is caused by a hinge that isn't plumb, meaning it's not aligned with the other hinges, so that the straight line that is drawn through one pin would continue to the other.

If this is the situation, you'll need loosen the screw and then move the hinge slightly backward or forward to close the gap. Once you've done this, it's also an ideal idea to tighten the hinge screws to ensure that everything is secured. After you've adjusted the hinges, you might need to move the strike plate opening closer to the stop molding on the door jamb. Finally, if you've shimmied the hinges, enlarged the strike plate hole, or moved the strike plate itself, you'll probably have to clean any holes from screws or gaps with a wood filler that matches the door frame.

If the methods above don't work, you can also rehang the door and reinstall the hinge pins. If you do this, ensure that you have a person to hold the door so that it does not fall. To remove the hinge pin, bend the blade of a large flathead screwdriver against the pin's base and tap it with a hammer to loosen and push the pin away. Then, Double glazing make sure that the hinges are shimmed where there are swings or binds, starting at the bottom of the door and moving towards the top. It is necessary to place some shims at each spot. It is crucial that they're made of the same material as your door hinges. Once the shims have been installed in the appropriate locations, you can tighten the hinge screws and hopefully your door will remain shut!

Repairing a door that won't close

If the door is not closing properly, there's a great possibility that it's rubbing something in the frame. This may be an edge of the hinges or a component of the latch mechanism or an opening in the strike plate that is too small for the door handle bolt to reach and lock repair near me. This issue can be fixed by tightening the hinge screws. If the door isn't closing then you can loosen them even further and then adjust the hinges so that they are more parallel.

In some cases the latch may contact the strike plate due to the fact that the bolt pocket is too high and isn't aligned with the strike plate's hole. To find out where the contact is taking place, put a strip of lipstick or similar marking material on the latch. Take a look at the mark as you open the door. This will tell you whether the latch is contacting with the strike plate hole and will help you fix the problem.

Depending on how much the strike plate must move, you might be able to expand the bolt pocket without moving the strike plate. If this isn't feasible then you can employ a screwdriver for moving the strike plate. Remove the screw holding the strike plate. Put the blade of a screwdriver into the hole, then hammer the top of the plate with the Hammer. Repeat this procedure a few times until the strike plate is placed in the correct position, and then screw it back in place.

If you have moved or enlarged the strike plate or bolt pocket, you will also have to fill in any old screw holes. You may also have to patch any gaps below or above the area where the strike plate is now situated. Wood filler that matches the color of your door's frame is ideal. Once you've completed this step your door should be shut properly and stay shut. If it doesn't, then you'll need to check the hinges for damage or looseness and replace any that are damaged.

Repairing a door that leaks

Water leaks around the door could cause problems for your house. Puddles that form around your exterior doors could indicate that the threshold or sill pan is damaged or your door was not installed properly, which can lead to massive water damage and mold.

The best way to stop leaks is to replace the old caulking. It is a good seal against the elements, but it may peel and crack over time, double glazed window repairs glazing (see more) leaving gaps through which water can get in. Use paintable and flexible sealants to ensure that they are able to withstand weathering.

The next step is to examine the frame of the door for signs of rot. This can happen to wood frames and doors if not addressed immediately. If you find rotting in the frame or door of a wooden wood it is necessary to take it out it and make any necessary repairs. Then, it's a great idea to apply a paint or stain to the wood.

If you don't see any signs of rot, it could be that air is leaking into the door frame molding. You can prevent this by filling the gaps with non-expanding foam or gap filler rod, or caulking. You can use spackle to make a quick and cheap repair.

While it's great to fix your own home window repairs near me whenever you can, certain tasks are best left to professionals. If your door has extensive or complicated damage, it's probably best to have a professional handle the window replacement. This will save you money and also provide you with the door that will last you for many years.

It is also important to consider whether your door is functionally or attractively appealing. Start by searching for the perfect door to match your needs and style. You can then be sure that the new upvc door repairs will perfectly into your home. When you've decided to go ahead with the installation, a professional will assist with the installation and Double Glazing ensure that your door appears its best.