• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high above the ground, navigating massive glass panes. They adhere to strict safety standards and frequently work in harsh weather conditions.

Wearing protective clothing, remove all glaze putty and glazing points using a utility knife. A heat gun can help soften the old glue and speed up removal.

Replacement

It is tempting to fix the glass of your window instead of replacing it when a pane breaks. However, replacing windows is typically more cost-effective, and can also aid in preventing other issues with your home's energy efficiency. Examine the kind of glass damaged to determine if it's a temporary fix or if a permanent solution is required.

The first step to repair a broken window is to remove the sash, also known as the frame and place it flat on a work table. Wearing eye protection, gently wiggle the window's frame and then remove any remaining shards. Utilize a utility blade to scrape off the glazing compound and the glazing points that keep the window in place. Keep track of the components and where they are to ensure they are reinstalled.

After the frame and sash are removed, you can begin preparing to install the new glass. Make sure you check the opening of the frame is the right size for your replacement window. Measure both ways across the opening, and then subtract 1/8 inch from each measurement to allow room for expansion and contraction of the frame and glass. After that, you can purchase double-strength glasses cut to these exact dimensions. It is also an excellent idea to buy enough new glazier's clips or glazier's points to be positioned every 6 inches around the window pane.

If the manufacturer is responsible for this, you can call them and file a claim. Once the new glass has been installed, it should be sprayed with a thin coating of the compound used by glaziers. After the compound has dried then you can paint it to match the rest of the frame.

If your crack is more than an inch in length You can stop it from expanding by slicing a small arc just beyond the crack. This technique isn't 100% infallible, but it will slow the development of the crack down to a manageable size until you can take permanent measures.

Repair

Professional window installers know how to handle various kinds of glass, and they have the tools needed to complete an excellent job. They also understand the best practices for disposing of garbage, which means they're less likely to leave crumbs behind, which could potentially hurt pets or family members. They're also familiar with different types of windows and may be aware of issues that might not be apparent to the uninitiated homeowner.

Wear safety goggles and gloves prior to starting repair work on cracked glass. A minor Glass Window Repair crack could cause shards to fly off, which could pose a risk to anyone who lives in or around the home. It's also important to determine the cause of the crack in the first place, since it can help prevent future problems.

Make a two-part mix of epoxy. They are typically 50/50 mixture of resin and hardener, and must be mixed quickly. Once the mixture is done, apply it to the crack in the glass and allow it to dry. It will take just some minutes, but it's essential to get it done quickly as the mixture is very dense and quick drying.

After the epoxy has dried, you can take off excess epoxy with a blade. After that, you'll need clean the area around the crack of glass. If you don't do this properly, the residue can cause further damage to the glass. Use a putty blade to smooth the compound around the edge of your window and then match it to the frame made of wood.

To make a more durable option think about using a plastic cover. You can cover the glass using masking tape or a sturdy trashbag. This will prevent the crack from spreading, and will also keep wind, water and bugs out.

You can create an interim solution when you are unable access the window in an efficient manner. Simply run a bead of the material around the outside edge of the broken pane. It won't completely fill the gap between the frame and glass but it will help keep the broken piece in place while you repair it.

Repainting

Repainting your old glass windows is a good idea. This is an affordable alternative to replace windows and give your house a new appearance. Before painting, make sure the surface is clean. Use soap or rubbing alcohol and water to wash away oil smudges, and other traces of dirt that can hinder paint from adhering. You should also wear rubber gloves while working on glass to avoid the risk of transferring your own oils onto the window's surface. Apply multiple thin coats instead of one thick coat. This will make the paint last longer and keep your windows looking smooth and even.

If you're planning to paint your glass windows, be sure you have the proper tools nearby. You will need either a brush or sponge painter's tap along with a ruler, toothpicks and a ruler. You should also have the brushes and paint you'll be using for the project on hand. Follow the instructions of the manufacturer. Have patience, as it may take a while for the paint to completely dry.

Also, ensure that the space you're working is well ventilated, especially if you're using solvent-based paint. This will decrease the risk of breathing into toxic chemicals and allow the paint to dry faster. Use a mask that is protective when using spray paints.

For older glass windows, you'll need to prepare the surface before painting. Use soap and warm water to thoroughly clean the glass window. Then, rub alcohol on any grease or oil residues that could interfere with the paint's adhesion. Be sure that the windows are completely dry before you begin to paint them.

If you have energy-efficient double glazed windows repair pane windows on your windows, it may be possible to make a claim for repair or replacement with the company that makes the windows or dealer who sold the windows. This is especially true if your windows are still under warranty and have experienced numerous issues with condensation or broken glass.

Sealing

Whether you have old double-pane windows with a cracked seal or newer insulated glass units (IGUs) that have experienced defogging, there are several methods for fixing the problem. It is the most expensive option to replace the insulated unit as well as the frame. However, it might be necessary if fog or condensation is causing energy loss. Other options include replacing the IGU with a single pane or fixing it by drilling a small hole in the bottom of the unit and filling the solution with anti-fog.

You can also seal up the gap between the window frame and the threshold or sill using a felt strip or vinyl v-strip. Felt is cheap and can be fixed by gluing, nailing or stapled to the frame but it doesn't provide much protection from moisture. Vinyl weather stripping that is v-strip is strong and easy to install, but it can be costly and is typically reserved for areas exposed to high abrasion. Door sweeps are able to be easily nailed to the floor and are affordable. However, they provide only a small amount of protection between the threshold and air.

To repair a damaged window seal first, you must use a putty knife to remove the old caulk. Wearing gloves and eye protection take care to remove the glazing points -- small fasteners that pin the glass in the frame's recess with sharp edges and pointed edges. Once you have removed the glazing points, scrub the grooves and sand the wood to a smooth finish. Clean any sanding residue and then seal the unfinished wood with a linseed oil-based paint or clear wood sealer.

Traditional glazing putty can be applied using a putty knife or caulking gun, but a knife provides a better application that is more precise and will provide a better seal. Make sure you choose a putty specifically designed for glass windows, since it will be more adhesive and long-lasting.

Apply a small amount of the putty to the inside edge of the frame, where it meets the glass. Slide the window into the frame so that scribed line on glass aligns with edge of frame. Apply pressure to the glass to force the putty into a tight seal. Smooth the compound with gloves and then remove any drips or caulk that were not properly applied before it has dried.