• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is a simple and affordable method to boost your home's security. The process is not for everyone. It requires a certain amount of skill and perseverance.

It is necessary to replace the cylinder that is inside the knob's body. The cylinder is responsible to recognize the key when it is put into the lock.

Removal of the old lock

The first step to replace the door lock is to get rid of the old lock. It's a fairly simple procedure, but there are a few things to be aware of. First, make sure that your new lock is the correct size for the door you have. This will ensure that it is securely fitted and won't create a gap around the deadbolt or latch.

After you've removed the latch plate look for two bolts or screws on the inside of the casing that connect the casing and two halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock off the door. If you have a mortise locking mechanism there is an anchor screw that connects the handle to the spindle. Take off the doorknobs by removing this screw using a screwdriver.

Remove the deadbolt as well as the latch plug from your door jamb. Install your new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the edge of your door to ensure that the new lock will fit.

Many reasons could cause you to replace the door lock, for instance suspecting that someone else has the key or Door Lock Change if you're welcoming the arrival of a new roommate. You could save money if you remove the lock yourself instead of hiring an expert. It's easier than most people think, and it can be done in a few minutes.

Remove the trim and handle from your door. Then, Door Lock Change pull the trim off with a flat screwdriver. You should be able to twist off most of it, and in some instances the handles could come off entirely. Next, search for a pinhole on the inside of the handle, and insert straightened clips into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look for a small tab on the interior of the lock and push it using a flat screwdriver. After the spindle is removed, you are able to remove the cylinder and the housing.

The process of selecting a new lock

There are many options to choose from when it comes time to pick a new lock. Take a look at various kinds of locks, and choose one that is compatible with the style of your door. Consider the backset (the distance between the edge of the door and the center of the hole for the lock) and the cross bore (small hole in the frame of the door frame). Select a lock that will fit the door's thickness and the swing.

The American National Standards Institute and BHMA have graded the majority of upvc door lock repairs locks to give an idea of their longevity and how difficult it is to pick them or disable them. A lock of grade 3 could be ideal for a peaceful apartment building in the countryside, whereas locks of grade 1 could be more suitable for an area with a lot of traffic, such as an open-air storefront.

Most smart door locks require a digital code to open. If you're worried about hacking, or other security issues, talk to a professional locksmith.

Replacing the cylinder

If the cylinder of your door lock is damaged or broken it can be replaced in just a few minutes using a simple DIY project. The trick is to select the correct cylinder and follow the directions that are included with it. The first step is to remove the handle or knob in the event that one is present then loosen the trim that is attached to the base of the lock cylinder with the help of a screwdriver. After the trim is removed, it is possible to remove the screws holding the cylinder with a flathead. The cylinder can then be gently lifted out of the door.

Before installing the new cylinder, make sure that it's the right length for the door you are using. With a tape measure, measure the distance between the cylinder's center and its left and right sides. Then, buy a new cylinder with the same measurements. This will stop the cylinder from snapping, which could happen when the door is kicked in or when the key gets stuck inside.

If you have a replacement cylinder, put it into the door and turn the key. This will ensure that the cylinder is in alignment with the carrier, which is usually located on the outside of the lock. You can then loosen the set screws that should be just a couple of turns inside the head. If there is a screw at the outside of the case, which holds the door, you will need to remove it.

After you have removed the lock cylinder, you can replace it with the new lock by sliding the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the piece that connects the cylinder with the lock indicator stem and this can be done by pulling up three small tabs on back of the cylinder using needle-nose pliers. Then, you'll be able to attach the smaller bracket to the back of the cylinder. You must then install the strike plate and latch plate, as well as the retaining rings that are attached to the top of the lock cylinder.

Installing the new lock

If you're replacing door locks an old lock, you should start by taking measurements of the width of the door. Most locksets for residential use come with a thickness of 3/8 to 1 3/4 inches. If your door is thicker, you will need a thick door kit that includes longer screws and longer tail pieces (for door lock replacement near me knobs) or spindle extensions (for deadbolts).

Most locks come with a comprehensive installation guide to aid you. Read the instructions carefully prior to beginning the process to ensure that you've followed all of the necessary steps. The manual will also provide you with an idea of the degree of skill required to accomplish the task. You might want to ask a friend who has experience changing locks for assistance if are changing a lock the first time.

It's a good idea to tape the openings in the old hardware before installing the new lock. This will stop screws from slipping through the holes, and protect any tiles you may have put in. It also shields your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of painter's tape designed to be used for this purpose, however you can also use gaffer's or masking tape if you have it available.

After you have removed the screws that hold the interior half of the lock section to the outside side immediately, pull it back. This must be done quickly to avoid the lock from accidentally closing and damaging the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure to place it in the proper position, which will be indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Attach the deadbolt to the jamb of the door. Test the deadbolt by throwing it several times to make sure that it is extended all the way through the strike plate and is completely secured. Follow the instructions that come with your electronic smart lock to program it. This involves downloading an application and registering your email address, verifying your identity and connecting to the wireless network in order to connect your device.